|
|
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
Advanced Wired / Wireless AutoDial Security Alarm System
[SY]
USD 129.99
USD 78.99
MUSIC Input RGB LED Controller + RF Remote Control
[LXM]
USD 55.00
USD 32.00
83-mode RGB LED Lighting Set - VALUE SET A
[Value Set A]
USD 210.00
USD 145.00
5-meter Million-colour 5050 SMD RGB 150 LEDs Light Strip (adhesive backing)
[L30M5(B)]
USD 89.00
USD 48.00
NEW Wireless/wired IP Camera with MOBILE VIEW FUNCTION (BLACK/WHITE)
[SV]
USD 129.99
USD 64.99
All-in-1 H.264 IP/Network Camera with MOBILE VIEW FUNCTION
[RV]
USD 220.00
USD 159.99
secBo series - GSM Wireless Smart Alarm System (Dual Band 900/1800MHz)
[SB-GL8088]
USD 299.99
USD 199.99
Energy-saving 3 LED Light Bulb GU10 (White)
[LYA]
USD 12.99
USD 7.99
|
|
 |
 |
 |
 |
|
|
|
|
|
 |
www.noviBo.com
 |
I press the arrow keys and hold down for about 60 seconds, it has no effect at all. WHY?
|
|
|
You need to press the DIY button first to change to DIY colour mode, then the arrow buttons will take effect.
|
|
|
|  |
|
secBo series - GSM Wireless Smart Alarm System
The unit doesn't send text messages, neither make phone calls. How to solve this problem?
|
|
|
|
First of all, please make sure you have connected the antenna to the alarm host. Then, please try to follow the power on sequence below:
1) Do not turn on the DC voltage. Plug the AC power adaptor to the alarm host first.
2) After the system finished initialization, please see if the GSM LED flash.
3) If the GSM LED flashed, turn on the DC voltage switch as well.
4) Try to trigger the alarm to see if it can call/sms you. Or you can try to call the alarm host as well.
Please also make sure the following conditions for the SIM card:
2) The SIM card is not password protected.
3) The SIM card does not have any phone number stored.
4) The SIM card has enough credits to make/receive phone calls.
Please feel free to let us know if you have any other question.
|
|
|
| |
|
How can I connect the GSM module (SG/SGF) to my alarm system?
|
|
|
|
 |
Required items to work with GSM Dialer
1.An unlock GSM SIM card suitable for an ordinary 2G phone. (GSM900/1800 Mhz for model SG; GSM850/900/1800/1900 Mhz for model SGF)
2.A 12Vdc power supply (included in the dialer set)
3.Antenna (included in the dialer set)
4.Telephone cable
5.Landline Telephone (maximum range voltage: 48V)
Connection Instruction
1.Insert the SIM card to the GSM module; connect the antenna and the power supply to switch on the unit.
2.After initialization, if the signal is good and enter into the correct state, then there will be a vertical signal bar showing on the right hand side of the screen.
3.Connect the GSM module phone port 1 to the telephone or a compatible alarm system with a telephone cable.
Tips
1.SIM card is not password protected.
2.SIM card has enough credits in it to make phone calls.
3.You have connected the antenna to the GSM module.
4.You connect the telephone to port 1 of the module and nothing else.
5.The SIM card is using the same GSM frequency as the module.
|
|
|
| |
|
What is the default password for alarm system SC?
|
|
|
|
1234 - Please refer to page 3 of the manual.
|
|
|
| |
|
How can I partial arm zone 2 to zone 5 of alarm system SC indepedently?
|
|
|
|
To control zone 2 to 5 independently, set as follow:
To open zone 2 (enable): password + partarm + 1
To close zone 2 (disable): password + partarm + 2
To open zone 3 (enable): password + partarm + 3
To close zone 3 (disable): password + partarm + 4
To open zone 4 (enable): password + partarm + 5
To close zone 4 (disable): password + partarm + 6
To open zone 5 (enable): password + partarm + 7
To close zone 5 (disable): password + partarm + 8
|
|
|
| |
|
How to connect the RFID keypad (SA), strike lock and the power supply?
|
|
|
|
To connect the keypad (1), strike lock (2) and the power supply (3):
(3) pin 4 to (1) pin 2 (GND conection)
(3) pin 5 to (1) pin 1 (+12V conection)
(3) PUSH to (1) PUSH (Push connection)
(2) +ve to (3) pin 7 (strike lock +ve pin to the supply NC pin)
(2) -ve to (3) pin 8 (strike lock +ve pin to the supply COM pin)
You can connect the door bell to the keypad.
You can connect the door release switch to (3) pin 1 and pin 4.
In the keypad, due to manufacturering error, the jumper needs to be set as NO instead of NC.
|
|
|
|
|
|
 |
